Skip to content
Sunday 22 November 2026 · Automotive technology news for engineers

ZF Develops High Revolution Drive With Half The Magnet Mass

ZF has developed the High Revolution Drive, a 3-in-1 electric drive spinning at up to 30,000 rpm that needs 50 percent less magnet mass and is nearly 25 percent smaller and lighter than a comparable SELECT drive, with production targeted by 2030.

ATN Editorial Team Source: press.zf.com 5 min read
ZF High Revolution Drive units shown inside a cutaway electric SUV driving on a motorway
Credit: ZF.

Summary: ZF has developed the High Revolution Drive, a compact 3-in-1 electric drive that spins at up to 30,000 rpm. Running the motor faster allows a smaller, lighter electric motor with reduced magnet requirements, while a high-ratio two-stage transmission delivers the required torque at the wheel. The drive is a variant of ZF’s modular SELECT platform, and ZF is in talks with several automakers, targeting production by 2030.

Key engineering takeaway: At the same power output, higher rotational speed reduces the motor torque required, and because torque is closely linked to rotor volume, the motor can shrink. In the High Revolution Drive, a two-stage spur gear transmission with a ratio of about 18:1 turns that speed into torque at the wheels. The version shown delivers 200 kW peak output and 3,500 Nm peak wheel torque. Compared with a SELECT drive running at 18,000 rpm, ZF says it is nearly 25 percent smaller and nearly 25 percent lighter, needs 50 percent less magnet mass, and reaches an efficiency of nearly 93 percent, on par with the comparable SELECT system.

Why it matters: ZF says the 50 percent cut in magnet mass lowers costs and reduces dependence on critical supply chains, and that the lower weight helps increase electric range. Because the High Revolution Drive builds on the existing SELECT platform and uses existing technologies, ZF says automakers can bring it into new vehicles faster and at lower development cost. It is aimed at the high-volume passenger car market, with outputs of approximately 150 to 200 kW on 400- and 800-volt systems.

  • Up to 30,000 rpm with low noise, backed by decades of transmission expertise
  • Compact design makes it easier for vehicle manufacturers to integrate the drive into new vehicle architectures
  • Scalable architecture makes the drive suitable for different power ratings and both 400- and 800-volt platforms

ZF has developed the High Revolution Drive, a compact 3-in-1 electric drive that spins at up to 30,000 rpm, so it’s smaller and lighter than conventional drives while delivering the same power. This enables a smaller, lighter electric motor with reduced magnet requirements. A high-ratio two-stage transmission delivers the required torque at the wheel. The new drive concept builds on the existing SELECT platform, so automakers can bring it into new vehicles faster and at lower development cost.

The motor speed of the High Revolution Drive is significantly higher than that of conventional systems. Making that work requires the whole system to work together: “The High Revolution Drive draws on ZF’s full systems expertise,” says Thomas Meiser, Head of the E-Mobility Business Unit at ZF. “Rather than optimizing individual components in isolation, we systematically coordinate the electric motor, power electronics and transmission.”

The principle is simple: At the same power output, a higher rotational speed reduces the required motor torque. Since torque is closely linked to rotor volume, the electric motor can be designed to be smaller and lighter. To turn that high speed into usable torque, a two-stage spur gear transmission with a ratio of about 18:1 makes sure the required torque reaches the wheels. The version shown delivers peak output of 200 kW and peak wheel torque of 3,500 Nm.

How The High Revolution Drive Controls Noise At 30,000 Rpm

Higher speeds make noise and vibration harder to control. ZF tackles this with decades of gear and transmission experience. ZF addresses these challenges through the coordinated design of the components: “Robustness and low noise and vibration levels were stringent development targets from the outset,” says Meiser. “To achieve this, we considered the electric motor, gearing, bearings and tooth geometry as an integrated system. For the configuration presented, 30,000 rpm is the economic and technical sweet spot.”

Magnet Mass, Weight And Efficiency Against A SELECT Drive

The High Revolution Drive is nearly 25 percent smaller and nearly 25 percent lighter than a comparable SELECT drive running at 18,000 rpm. The required magnet mass is reduced by 50 percent, which lowers costs and reduces dependence on critical supply chains. Even at high rotational speeds and with a high gear ratio, the system achieves an efficiency of nearly 93 percent, on par with the comparable SELECT system.

The lower weight also helps increase electric range. The focus is on the high-volume passenger car market, with drive outputs of approximately 150 to 200 kW. The architecture is scalable for different power ratings and for both 400- and 800-volt systems.

Built As A Variant Of The Modular SELECT Platform

The approach also follows ZF’s platform strategy: The High Revolution Drive is designed as a variant of the modular SELECT platform and uses existing technologies. This keeps product costs predictable while giving automakers flexibility in how the drive is produced. “With SELECT, we do not have to start from scratch for every new drive variant,” says Meiser. “We use our modular system to tailor new concepts to different customer requirements.”

ZF is already in talks with several automakers and is targeting production by 2030.

ZF High Revolution Drive: Frequently Asked Questions

What is the ZF High Revolution Drive?

The ZF High Revolution Drive is a compact 3-in-1 electric drive that combines an electric motor, power electronics and a two-stage transmission, with motor speeds of up to 30,000 rpm. ZF has designed it as a variant of its modular SELECT platform for the high-volume passenger car market, with drive outputs of approximately 150 to 200 kW.

Why does a higher motor speed allow a smaller electric motor?

For a given power output, power is the product of torque and rotational speed, so running a motor faster means it needs to produce less torque. Torque is closely linked to rotor volume, so a lower-torque motor can be made smaller and lighter. A reduction gear then multiplies the torque back up before it reaches the wheels; in the High Revolution Drive that is a two-stage spur gear transmission with a ratio of about 18:1.

How much smaller and lighter is the High Revolution Drive?

ZF says it is nearly 25 percent smaller and nearly 25 percent lighter than a comparable SELECT drive running at 18,000 rpm, with the required magnet mass reduced by 50 percent and an efficiency of nearly 93 percent, on par with the comparable SELECT system.

What power and voltage does the High Revolution Drive support?

The version shown delivers peak output of 200 kW and peak wheel torque of 3,500 Nm. ZF says the architecture is scalable for different power ratings and for both 400- and 800-volt systems.

When will the ZF High Revolution Drive go into production?

ZF says it is already in talks with several automakers and is targeting production by 2030.

Further Reading

For more EV news, click here.

Source

The latest technology and engineering news direct to your inbox.

ATN publishes first-party announcements within seven days of release. The summary at the top is written by ATN for engineers; the text below it is the company's own.